Основы робототехники

Arduino библиотеки

On this page. (hide)

Overview

The Intel® Galileo Gen2 is a board based on the Intel® Quark™ SoC X1000, a 32-bit Intel® Pentium® processor-class system on a chip ( SoC ), operating at speeds up to 400MHz.

The Quark processor supports the Yocto 1.4 Poky Linux distribution.

The board has built-in Ethernet with support for Power Over Ethernet( PoE ), a USB 2.0 Host Port, micrso-SD slot, PCI Express mini-card slot, 20 digital input/output pins (of which 6 can be used as PWM outputs with 8/12-bits of resolution and 6 as analog inputs with 12 bits of resolution), a micro USB connection, an ICSP header, a JTAG header, and 2 reset buttons.

There is also an integrated Real Time Clock (RTC), with an optional 3V “coin cell” battery for operation between turn on cycles.

The Intel® Galileo Gen2 supports shields that operate at either 3.3v or 5v. The board is designed to be hardware and software pin-compatible with Arduino shields designed for the Uno R3. Digital pins 0 to 13 (and the adjacent AREF and GND pins), Analog inputs 0 to 5, the power header, ICSP header, and the UART port pins (0 and 1), are all in the same locations as on the Arduino Uno R3.

Visit the Intel® Board Documentation page for further informations.

Supported Arduino libraries

The software release supports the following Arduino libraries:

SPI
EEPROM
UART
GPIO
Wi-Fi
Servo
USB Host

Supported Arduino shields

A list of the supported Arduino shields can be found here.

Summary

Microcontroller SoC Quark X1000
Operating Voltage 3.3V / 5V
Input Voltage 7-15V
Digital I/O Pins 14 (of which 6 provide 8/12-bit PWM output)
Analog Input Pins 6
Flash Memory 512 kB
RAM 256 MB DDR3
SRAM 512 kB
Flash Storage 8MB
EEPROM 8kB
Clock Speed 400 MHz
PoE compatible
Length 124 mm
Width 72 mm

Differences

Differences between the Intel® Galileo Gen2 and the Intel® Galileo

The earlier Intel Galileo did not have an on-board regulator, so the power supply had to be exactly 5V. The Intel Galileo Gen2 has on-board regulator, so it may be powered with any suitable supply providing 7-15 VDC.

Differences between the Arduino Yùn and the Intel® Galileo Gen2

The Arduino Yùn has two processors: One runs Linux, and an Atmel microcontroller runs the Arduino sketch. The Intel® Galileo Gen2 has one processor. In addition to running Linux, this processor runs the Arduino sketch.

Differences between the Intel® Galileo Gen2 and all Arduinos

Note that a sketch loaded into the Intel® Galileo Gen2 is lost after a power cycle. It is possible to boot the Intel® Galileo Gen2 from a uSD card, and in that case to restore a sketch from the same card. Instructions for doing so are forthcoming.

On-board Linux

The Yocto 1.4 Poky Linux distribution is installed on your Intel Galileo Gen2. You can access various Linux functions with the system() call.

Power

The Intel® Galileo Gen2 can be powered only via an external power supply. The adapter can be connected by plugging a 2.1mm center-positive plug into the board’s power jack. The board can operate on an external supply of 7 to 15 volts. The provided power supply provides 12v.

The power pins are as follows:

  • VIN: The input voltage to the Intel® board. You can access the voltage supplied via the power jack through this pin.
  • 5V: This pin outputs a regulated 5V from the regulator on the board.
  • 3.3V: A 3.3 volt supply generated by the on-board regulator. This regulator also provides the power supply to the Quark microcontroller.
  • GND: Ground pins.
  • IOREF: This pin on the Arduino board provides the voltage reference with which the microcontroller operates. This can be 3.3V or 5V based on the IOREF jumper position.
  • 12V power-over-Ethernet ( PoE ) capable

Buttons

There are 2 reset buttons with different functions on the board:

  • Reboot: resets the Quark X1000 processor
  • Reset: resets sketch and any attached shield

Memory

The Quark X1000 has 512kB of embedded SRAM.

The board has an additional 256 MB DDR3 Ram amd 8MB of Flash to store firmware and the Arduino sketch. It’s possible to update the firmware using the IDE. The on board uSD supports uSD card up 32G, and can be used to provide a complete Yocto 1.4 Poky Linux image.

Input and Output

  • Serial: 0 (RX) and 1 (TX). Used to receive (RX) and transmit (TX) TTL serial data.
  • Digital I/O: Digital pins 0 through 13 and Analog pins A0 through A5 can be used as a digital input or output, using pinMode(), digitalWrite(), and digitalRead() functions. They can operate at 3.3 or 5 volts.

Each pin can provide (source) or receive (sink) a current of 16mA @ 5v, or a current of 8mA@3.3V

  • PWM: Pins 3,5,6,9,10, and 11
  • Provide 8/12bit PWM output with the analogWrite() function. The resolution of the PWM can be changed with the analogWriteResolution() function.
  • These pins support SPI communication using the SPI library.
  • Each analog input provide 10/12 bits of resolution. The resolution can be changed with the analogReadResolution() function.

There are 2 reset buttons with different functions on the board:

  • Reboot:
  • resets the Quark X1000 processor
  • resets sketch and attached shield

Communication

The Intel® Galileo Gen2 has a number of facilities for communicating with a computer, another Galileo, Arduino or other microcontrollers, and different devices like phones, tablets, cameras and so on.

It provides 2 UART Controllers : UART 0 to Galileo headers 0, 1; UART 1 to 6-pin 3.3V USB TTL FTDI header; optionally directed to Galileo headers 2, 3 .

The Native USB port can also act as a USB host for connected peripherals such as mice, keyboards, and smartphones. To use these features, see the USBHost reference pages. The onboard microSD card reader is accessible through the SD Library. The communication between Galileo and the SD card is provided by an integrated SD controller and does not require the use of the SPI interface like other Arduino boards.

The onboard Ethernet interface is fully supported, use the Ethernet Library. It does not require the use of the SPI interface like existing Arduino shields.

The Arduino software includes a Wire library to simplify use of the TWI/I2C bus; see the documentation for details. For SPI communication use the SPI library.

The board provides also a mini PCI Express (mPCIe) slot. This slot allows full size and half size (with adapter) mPCIe modules to be connected to the board and also provides an additional USB Host port via the slot. Any standard mPCIe module can be connected and used to provide applications such as WiFi , Bluetooth or Cellular connectivity.

Programming

The Intel® Galileo Gen2 can be programmed with this special version of the Arduino software. It’s possible to make requests of the Linux kernel with system() calls. This gives your Arduino sketch access to powerful utilities like Python, Node.js, OpenCV , and all sorts of fun Linux stuff.

Note that Intel® Galileo Gen2 forgets the sketch after powering down. It is possible to booth the Galileo Gen2 from the uSD card, and in that case, to restore a sketch from the same card. Instructions for that will be forthcoming.

Further documentation

For detailed documentation please refer to the Intel Documentation. In order to get started with your board please visit the getting started page


Источник: www.arduino.cc